Фильтр :
Стандарт и/или проект находящийся в компетенции ISO/TC 213 Секретариата | Этап | ICS |
---|---|---|
Standard reference temperature for industrial length measurements
|
95.99 | |
Geometrical Product Specifications (GPS) — Standard reference temperature for geometrical product specification and verification
|
95.99 | |
Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties
|
95.99 | |
Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties
|
60.60 | |
ISO system of limits and fits — Part 1: Bases of tolerances, deviations and fits
|
95.99 | |
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits
|
90.93 | |
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1
|
60.60 | |
ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts
|
95.99 | |
ISO system of limits and fits — Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
|
90.93 | |
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1
|
60.60 | |
ISO system of limits and fits — Part I : General, tolerances and deviations
|
95.99 | |
Toleranced dimensions — Conversion from inches into millimetres and vice versa
|
95.99 | |
Technical drawings — Tolerancing of linear and angular dimensions
|
95.99 | |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
|
90.92 | |
Dial gauges reading in 0.01 mm, 0.001 in and 0.0001 in
|
95.99 | |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1
|
60.60 | |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2
|
60.60 | |
Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
|
30.00 |
|
Surface roughness — Parameters, their values and general rules for specifying requirements
|
95.99 | |
Technical drawings — Geometrical tolerancing — Tolerancing of form, orientation, location and run-out — Generalities, definitions, symbols, indications on drawings
|
95.99 | |
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
|
90.93 | |
Series of conical tapers and taper angles
|
95.99 | |
Geometrical Product Specifications (GPS) — Series of conical tapers and taper angles
|
95.99 | |
Geometrical product specifications (GPS) — Series of conical tapers and taper angles
|
90.93 | |
Geometrical Product Specifications (GPS) — Indication of surface texture in technical product documentation
|
95.99 | |
Technical drawings — Dimensioning and tolerancing of profiles
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing
|
90.93 | |
Selection of tolerance zones for general purposes
|
95.99 | |
Classification of instruments and devices for measurement and evaluation of the geometrical parameters of surface finish
|
95.99 | |
Instruments for the measurement of surface roughness by the profile method — Vocabulary
|
95.99 | |
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of progressive profile transformation — Profile recording instruments
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size
|
90.92 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size
|
30.60 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges
|
90.93 | |
ISO system of limits and fits — Part II : Inspection of plain workpieces
|
95.99 | |
System of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengths from 6 to 630 mm
|
95.99 | |
Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes
|
90.20 | |
Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing
|
90.20 | |
Limits and fits — Series of angles and slopes on wedges and prisms
|
95.99 | |
Geometrical Product Specifications (GPS) — Series of angles and slopes on prisms
|
95.99 | |
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
|
95.99 | |
Roughness comparison specimens — Part 1: Turned, ground, bored, milled, shaped and planed
|
95.99 | |
Roughness comparison specimens — Part 2: Spark-eroded, shot blasted and grit blasted, and polished
|
95.99 | |
Roughness comparison specimens — Part 2: Spark-eroded, shot-blasted and grit-blasted, and polished
|
95.99 | |
Roughness comparison specimens — Part 3: Cast surfaces
|
95.99 | |
Technical drawings — Geometrical tolerancing — Maximum material principle
|
95.99 | |
Technical drawings — Geometrical tolerancing — Maximum material principle — Amendment 1: Least material requirement
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
|
60.60 | |
General tolerances — Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
|
90.92 | |
General tolerances — Part 2: Geometrical tolerances for features without individual tolerance indications
|
95.99 | |
Permissible machining variations in dimensions without tolerance indication
|
95.99 | |
General tolerances
|
30.00 |
|
Technical drawings — Dimensioning and tolerancing — Cones
|
95.99 | |
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones
|
95.99 | |
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones
|
90.93 | |
Instruments for the measurement of surface roughness by the profile method — Contact (stylus) instruments of consecutive profile transformation — Contact profile meters, system M
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
|
90.92 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments — Technical Corrigendum 1
|
60.60 | |
Vernier callipers reading to 0,1 and 0,05 mm
|
95.99 | |
Micrometer callipers for external measurement
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of micrometers for external measurements
|
60.60 | |
Gauge blocks
|
95.99 | |
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks
|
90.93 | |
Geometrical Product Specifications (GPS) — Length standards — Gauge blocks — Technical Corrigendum 1
|
60.60 | |
Blanks for plug gauges and handles (taper lock and trilock) and ring gauges — Design and general dimensions
|
95.99 | |
Surface roughness — Terminology — Part 1: Surface and its parameters
|
95.99 | |
Surface roughness — Terminology — Part 2: Measurement of surface roughness parameters
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Amendment 1: Peak count number
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Technical Corrigendum 1
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters — Technical Corrigendum 2
|
95.99 | |
Rules and procedures for the measurement of surface roughness using stylus instruments
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Rules and procedures for the assessment of surface texture — Technical Corrigendum 1
|
95.99 | |
Methods for the assessement of departure from roundness — Measurement of variations in radius
|
90.93 | |
Methods for the assessment of departure from roundness — Measurement by two- and three-point methods
|
95.99 | |
Geometrical product specifications (GPS) — Association
|
60.60 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Design and metrological characteristics of two-point inside micrometers
|
40.99 | |
System of cone fits for cones from C = 1 : 3 to 1 : 500, lengths from 6 to 630 mm and diameters up to 500 mm
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 1: Material measures
|
90.93 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 1
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards — Technical Corrigendum 2
|
95.99 | |
Geometrical product specifications (GPS) — Surface texture: Profile method; Measurement standards — Part 2: Software measurement standards
|
90.93 | |
Calibration specimens — Stylus instruments — Types, calibration and use of specimens
|
95.99 | |
Geometrical Product Specifications (GPS) — Geometrical tolerancing — Positional tolerancing
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Pattern and combined geometrical specification
|
90.93 | |
Technical drawings — Geometrical tolerancing — Datums and datum-systems for geometrical tolerances
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
|
95.99 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems
|
60.60 | |
Technical drawings — Geometrical tolerancing — Tolerancing of form, orientation, location and run-out — Verification principles and methods — Guidelines
|
95.99 | |
Geometrical product specifications (GPS) — Rotary axis form-measuring instruments — Design and metrological characteristics
|
60.60 | |
Measurement of roundness — Terms, definitions and parameters of roundness
|
95.99 | |
Vernier callipers reading to 0,02 mm
|
95.99 | |
Height setting micrometers and riser blocks
|
95.99 | |
Technical drawings — Fundamental tolerancing principle
|
95.99 | |
Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 1: Vocabulary
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions
|
60.60 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system
|
60.60 | |
Castings — System of dimensional tolerances
|
95.99 | |
Castings — System of dimensional tolerances and machining allowances
|
95.99 | |
Surface plates — Part 1: Cast iron
|
90.93 | |
Surface plates — Part 2: Granite
|
90.93 | |
Geometrical Product Specification (GPS) — Surface imperfections — Terms, definitions and parameters
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Dial test indicators (lever type) — Design and metrological characteristics
|
90.93 | |
Geometrical product specifications (GPS) — Drawing indications for moulded parts in technical product documentation (TPD)
|
90.93 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary
|
90.93 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 1: Vocabulary — Technical Corrigendum 1
|
60.60 | |
Coordinate metrology — Part 2: Performance assessment of coordinate measuring machines
|
95.99 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring size
|
95.99 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring linear dimensions
|
90.93 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 3: CMMs with the axis of a rotary table as the fourth axis
|
90.93 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode
|
95.99 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode — Technical Corrigendum 1
|
95.99 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using multiple-stylus probing systems
|
95.99 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using single and multiple stylus contacting probing systems
|
95.99 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 5: Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and/or scanning measuring mode
|
60.60 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features
|
90.93 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 6: Estimation of errors in computing Gaussian associated features — Technical Corrigendum 1
|
60.60 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 7: CMMs equipped with imaging probing systems
|
90.93 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 8: CMMs with optical distance sensors
|
90.93 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 9: CMMs with multiple probing systems
|
90.93 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers for measuring point-to-point distances
|
95.99 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers
|
60.60 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 12: Articulated arm coordinate measurement machines (CMM)
|
90.93 | |
Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 13: Optical 3D CMS
|
60.60 | |
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3
|
30.60 | |
Technical drawings — Tolerancing of orientation and location — Projected tolerance zone
|
95.99 | |
Technical drawings — Dimensioning and tolerancing — Non-rigid parts
|
95.99 | |
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts
|
90.93 | |
Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts — Technical Corrigendum 1
|
60.60 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Metrological characteristics of phase correct filters
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Metrological characteristics of phase correct filters — Technical Corrigendum 1
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Motif parameters
|
90.93 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Motif parameters — Technical Corrigendum 1
|
90.93 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Profile — Calibration of contact (stylus) instruments
|
30.60 |
|
Geometrical product specifications (GPS) — Cylindricity — Part 1: Vocabulary and parameters of cylindrical form
|
90.93 | |
Geometrical Product Specifications (GPS) — Cylindricity — Part 1: Vocabulary and parameters of cylindrical form
|
95.99 | |
Geometrical product specifications (GPS) — Cylindricity — Part 2: Specification operators
|
90.93 | |
Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators
|
95.99 | |
Geometrical Product Specifications (GPS) — Cylindricity — Part 2: Specification operators — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Roundness — Part 1: Vocabulary and parameters of roundness
|
90.93 | |
Geometrical Product Specifications (GPS) — Roundness — Part 1: Vocabulary and parameters of roundness
|
95.99 | |
Geometrical product specifications (GPS) — Roundness — Part 2: Specification operators
|
90.93 | |
Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators
|
95.99 | |
Geometrical Product Specifications (GPS) — Roundness — Part 2: Specification operators — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Straightness — Part 1: Vocabulary and parameters of straightness
|
90.93 | |
Geometrical Product Specifications (GPS) — Straightness — Part 1: Vocabulary and parameters of straightness
|
95.99 | |
Geometrical product specifications (GPS) — Straightness — Part 2: Specification operators
|
90.93 | |
Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators
|
95.99 | |
Geometrical Product Specifications (GPS) — Straightness — Part 2: Specification operators — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Flatness — Part 1: Vocabulary and parameters of flatness
|
90.93 | |
Geometrical Product Specifications (GPS) — Flatness — Part 1: Vocabulary and parameters of flatness
|
95.99 | |
Geometrical product specifications (GPS) — Flatness — Part 2: Specification operators
|
90.93 | |
Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators
|
95.99 | |
Geometrical Product Specifications (GPS) — Flatness — Part 2: Specification operators — Technical Corrigendum 1
|
95.99 | |
Geometrical product specification (GPS) — Coordinate measuring machines (CMM): Testing the performance of CMMs using single-stylus contacting probing systems
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment: Electronic digital-indicator gauge — Design and metrological characteristics
|
90.92 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment; Height gauges — Design and metrological characteristics
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological characteristics
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Design and metrological characteristics of callipers
|
90.60 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design and metrological characteristics
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Design and metrological characteristics of calliper depth gauges
|
60.60 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions
|
90.60 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 1: Filtering and general measurement conditions — Technical Corrigendum 1
|
60.60 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve — Technical Corrigendum 1
|
95.99 | |
Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 3: Height characterization using the material probability curve
|
95.99 | |
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with specifications
|
95.99 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving conformity or nonconformity with specifications
|
95.99 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
|
90.93 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
|
90.93 | |
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
|
95.99 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification — Technical Corrigendum 1
|
60.60 | |
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 3: Guidelines for achieving agreements on measurement uncertainty statements
|
90.93 | |
Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 3: Guidelines for achieving agreements on measurement uncertainty statements
|
95.99 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 4: Background on functional limits and specification limits in decision rules
|
90.93 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 5: Uncertainty in verification testing of indicating measuring instruments
|
90.93 | |
Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 6: Generalized decision rules for the acceptance and rejection of instruments and workpieces
|
60.60 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
|
90.92 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes
|
40.60 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes
|
95.99 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear or angular sizes
|
90.93 | |
Geometrical product specifications (GPS) — Dimensional tolerancing — Part 3: Angular sizes
|
90.93 | |
Geometrical product specifications (GPS) — Extraction
|
90.93 | |
Geometrical product specifications (GPS) — Matrix model
|
90.93 | |
Geometrical product specification (GPS) — Masterplan
|
95.99 | |
Geometrical Product Specifications (GPS) — Geometrical features — Part 1: General terms and definitions
|
95.99 | |
Geometrical Product Specifications (GPS) — Geometrical features — Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature
|
95.99 | |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
|
95.99 | |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment
|
90.93 | |
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 1: Overview and metrological characteristics
|
90.93 | |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece
|
30.60 | |
Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or measurement standards
|
90.93 | |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or standards
|
95.99 | |
Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 4: Evaluating task-specific measurement uncertainty using simulation
|
90.93 | |
Geometrical product specifications (GPS) — Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences
|
90.93 | |
Geometrical Product Specifications (GPS) — Linear and angular dimensioning and tolerancing: +/- limit specifications — Step dimensions, distances, angular sizes and radii
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic concepts
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic concepts
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters
|
90.92 | |
Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters
|
50.20 | |
Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters
|
90.92 | |
Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters
|
40.20 | |
Geometrical product specifications (GPS) — Filtration — Part 28: Profile filters: End effects
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 28: Profile filters: End effects
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: wavelets
|
60.60 | |
Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters
|
90.92 | |
Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters
|
50.20 | |
Geometrical product specifications (GPS) — Filtration — Part 32: Robust profile filters: Spline filters
|
60.60 | |
Geometrical product specifications (GPS) — Filtration — Part 32: Robust profile filters: Spline filters
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 40: Morphological profile filters: Basic concepts
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 40: Morphological profile filters: Basic concepts
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 41: Morphological profile filters: Disk and horizontal line-segment filters
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 41: Morphological profile filters: Disk and horizontal line-segment filters
|
95.99 | |
Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation
|
60.00 | |
Geometrical product specifications (GPS) — Filtration — Part 49: Morphological profile filters: Scale space techniques
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 49: Morphological profile filters: Scale space techniques
|
95.99 | |
Geometrical product specification (GPS) — Filtration — Part 60: Linear areal filters — Basic concepts
|
90.93 | |
Geometrical product specification (GPS) — Filtration — Part 61: Linear areal filters — Gaussian filters
|
90.93 | |
Geometrical product specification (GPS) — Filtration — Part 61: Linear areal filters — Gaussian filters — Amendment 1
|
60.60 | |
Geometrical product specifications (GPS) — Filtration — Part 62: Linear areal filters: spline filters
|
60.60 | |
Geometrical product specifications (GPS) — Filtration — Part 71: Robust areal filters: Gaussian regression filters
|
90.93 | |
Geometrical product specifications (GPS) — Filtration — Part 85: Morphological areal filters: Segmentation
|
90.93 | |
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
|
90.93 | |
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
|
95.99 | |
Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities
|
90.93 | |
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties
|
95.99 | |
Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators and uncertainties — Technical Corrigendum 1
|
95.99 | |
Geometrical product specifications (GPS) — General concepts — Part 3: Toleranced features
|
90.93 | |
Geometrical product specifications (GPS) — Basic concepts — Part 4: Geometrical characteristics for quantifying GPS deviations
|
90.93 | |
Geometrical product specification (GPS) — Tolerancing of moveable assemblies
|
90.93 | |
Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty for CMMs using single and multiple stylus contacting probing systems
|
90.93 | |
Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts
|
60.60 | |
Geometrical product specifications (GPS) — Partition — Part 2: Nominal model
|
60.60 | |
Geometrical product specifications (GPS) — Partition — Part 3: Methods used for specification and verification
|
60.60 | |
Geometrical product specifications (GPS) — Population specification
|
90.93 | |
Geometrical product specifications (GPS) — Decomposition of geometrical characteristics for manufacturing control
|
90.93 | |
Geometrical product specifications (GPS) — Transition specification
|
60.60 | |
Geometrical product specifications (GPS) — Types of documents with GPS
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Profile — Part 1: Indication of surface texture
|
60.60 | |
Geometrical product specifications (GPS) — Surface texture: Profile — Part 2: Terms, definitions and surface texture parameters
|
60.60 | |
Geometrical product specifications (GPS) — Surface texture: Profile — Part 3: Specification operators
|
60.60 | |
Geometrical product specifications (GPS) — Geometrical tolerancing — General geometrical specifications and general size specifications
|
60.60 | |
Geometrical product specifications (GPS) — Features utilized in specification and verification
|
90.93 | |
Geometrical product specifications (GPS) — Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Profile method — Flowchart for PSm, RSm, WSm and Pc, Rc, Wc
|
60.60 | |
Technical product specification (TPS) — Application guidance — International model for national implementation
|
95.99 | |
Technical product specification (TPS) — Application guidance — International model for national implementation
|
60.60 | |
Geometrical product specifications (GPS) — Association — Mathematical concepts
|
30.99 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 1: Indication of surface texture
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms, definitions and surface texture parameters
|
95.99 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms, definitions and surface texture parameters
|
60.60 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 3: Specification operators
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 6: Classification of methods for measuring surface texture
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 6: Classification of methods for measuring surface topography
|
30.20 |
|
Geometrical product specification (GPS) — Surface texture: Areal — Part 70: Material measures
|
90.92 | |
Geometrical product specification (GPS) — Surface texture: Areal — Part 70: Material measures
|
20.00 |
|
Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards
|
95.99 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards
|
30.60 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 72: XML file format x3p
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 72: XML file format x3p — Amendment 1
|
60.60 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 73: Terms and definitions for surface defects on material measures
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 600: Metrological characteristics for areal topography measuring methods
|
90.93 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 601: Nominal characteristics of contact (stylus) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 601: Design and characteristics of contact (stylus) instruments
|
50.20 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 602: Design and characteristics of non-contact (confocal chromatic probe) instruments
|
50.20 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 603: Design and characteristics of non-contact (phase shifting interferometry) instruments
|
50.20 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 604: Design and characteristics of non-contact (coherence scanning interferometry) instruments
|
50.20 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 605: Design and characteristics of non-contact (point autofocus probe) instruments
|
50.20 | |
Geometrical product specification (GPS) — Surface texture: Areal — Part 606: Nominal characteristics of non-contact (focus variation) instruments
|
90.92 | |
Geometrical product specification (GPS) — Surface texture: Areal — Part 606: Design and characteristics of non-contact (focus variation) instruments
|
30.60 |
|
Geometrical product specifications (GPS) — Surface texture: Areal — Part 607: Nominal characteristics of non-contact (confocal microscopy) instruments
|
90.92 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 607: Design and characteristics of non-contact (confocal microscopy) instruments
|
20.00 |
|
Geometrical product specifications (GPS) — Surface texture: Areal — Part 700: Calibration, adjustment and verification of areal topography measuring instruments
|
60.60 | |
Geometrical product specifications (GPS) — Surface texture: Areal — Part 701: Calibration and measurement standards for contact (stylus) instruments
|
90.93 | |
Geometrical product specifications (GPS) — Characteristics and conditions — Definitions
|
90.93 |
По запросу ничего не найдено. Пожалуйста, попробуйте изменить настройки фильтра.